← All guides

Carb and fuel line

Stihl BR 420 C Magnum

Swap the carburetor, the fuel line and the filter in the tank. About an hour, one screwdriver.

Photograph every step before you take it apart
Cold engine. Outdoors. No sparks, no smoking.
Have on hand

From the kit

New carburetor (it replaces Stihl carb 4203 120 0601)
Two carb gaskets
Fuel line, fuel filter and tank grommet
Air filter and choke knob

Tools

Torx T27 driver. Every screw on this job is the same Stihl size, and the tool that came with the blower fits them.
Needle-nose pliers or long forceps
A foot of stiff wire with a small hook bent on one end
Sharp knife or razor for the fuel line
Gas can to drain into, rags, a tray for screws

Fuel

Fresh 50:1 mix. That is 2.6 oz of two-stroke oil per gallon of gas.
Know this first

One fuel line. A single line runs from the tank to the carb. Stihl's parts list for this blower shows no primer bulb, so the bulb in the kit is a spare for other models. Look at yours before you start: if there is a bulb, there will be a second line, and it goes back the way it came off.

The new carb looks a little different. The Stihl carb has a small vent stub on top that pokes into a hole in the backplate. Most replacement carbs do not have it. That is normal and it still fits.

The engine cover has to come off. The carb sits behind the plastic cover on the starter side, so the starter comes off with it.

The parts, in order
Stihl exploded diagram of the air filter and carburetor
10 filter cover and 11 its two screws. 9 prefilter frame, 8 air filter. 1 filter housing, 2 the two long screws, 3 the short screws. 12 the two carb gaskets, 15 the carb, 17 the choke knob. 20 the flange the carb bolts to. 7 the breather hose. From Stihl's spare parts list.
Take it apart
1

Make it safe

Slide the stop switch to 0. Pull the rubber boot off the spark plug so the engine cannot fire.

2

Let the pressure out and drain

Loosen the fuel cap slowly. A warm tank holds pressure and will spit fuel out of a cut line. Then pour the old fuel into the gas can.

3

Air filter off

Undo the two screws on the filter cover on the left side. Pull off the cover, the paper filter and the prefilter frame behind it.

Filter cover off, filter housing showing
Filter cover and filter off. The black box left on the engine is the filter housing. Still from the Hipa Store video.
4

Engine cover off

Take out the four screws around the pull-rope starter, then the two screws at the top of the cover and the two at the bottom. Lift the starter and the cover away together. The carb is now in the open.

Engine cover off, carburetor exposed
Engine cover off. The carb is in the middle, the fuel tank and its cap below it, and the filter housing is hanging loose at the bottom. Still from the Hipa Store video.
5

Photograph the carb

Get the fuel line, the small breather hose, the throttle cable and the choke knob in the picture, from two sides.

6

Fuel line off the carb

Squeeze the small spring clip and slide it back along the line, then twist and pull the line off its stub. If it is stuck, slit the end with the knife. Pull the small breather hose off as well.

Pliers on the fuel line clip at the carburetor
Pliers on the spring clip where the fuel line meets the carb. Still from the Hipa Store video.
7

Carb screws out

Two long screws run through the filter housing and the carb into the engine, and one shorter screw holds the housing beside them. Take them out. The housing, a gasket, the carb and a second gasket come away as a stack.

8

Unhook the throttle cable

On the carb, turn the throttle lever by hand until the cable goes slack, then slide the cable end out of the small swivel on the lever. Keep the swivel if the new carb has none.

New fuel line and filter
9

See how it is laid out

The fuel tank sits low on the starter side, with its cap next to the carb. A shaped hose with a collar is pushed into a hole in the top of the tank, and the filter hangs on its inner end. A small elbow sits in the collar, and a short hose runs from the elbow up to the carb.

Carburetor with the fuel line running down into the tank
The fuel line runs from the carb down into the top of the tank, beside the cap. Still from the Hipa Store video.
Stihl diagram of the fuel tank, hoses and filter
Stihl's drawing. 19 is the shaped hose with its collar, 23 the filter, 20 the elbow, 21 the hose to the carb, 24 its clip, 22 the tank vent. From Stihl's spare parts list.
10

Pull the old hose and filter

Pull the elbow out of the collar, then work the collar out of the tank top and draw the hose and filter out through that hole. If the filter drops off inside, fish it out through the filler neck with the hooked wire.

11

Fit the new line

The kit's grommet takes the place of the collar: press it into the hole until its groove seats all the way around. Cut the end of the new line at a long slant, push it down through the grommet, hook it inside the tank and pull the end up out of the filler neck.

12

Fit the filter

Push the new filter onto the end and lower it back in. It should lie on the bottom of the tank with enough slack to reach every corner when the blower tips.

13

Cut to length

Stihl's hose from the tank to the carb is 6 1/2 in (166 mm). Leave that much outside the tank and trim the end square. Too long and it kinks under the cover, too short and it pulls off.

14

Check the vent

The small valve in the top of the tank lets air in as fuel goes out. If it is gummed shut the engine starves after a minute. Blow it clean or replace it.

Put it back together
15

Clean the mounting face

Wipe the face on the engine where the carb sits and pick off any old gasket. Nothing should fall into the intake hole.

16

Hook the throttle cable first

Fit the choke knob to the new carb, then slide the cable end into the swivel on the throttle lever. It is much harder once the screws are in.

17

Build the stack

Gasket, carb, gasket, filter housing. The gasket against the engine has a small extra hole: line it up with the matching hole in the engine side. That hole drives the fuel pump inside the carb. Covered up, the engine will not draw fuel.

Filter housing with a gasket on its back
The filter housing with its gasket. Still from the Hipa Store video.
New carburetor held against the engine
The new carb going on. Still from the Hipa Store video.
18

Screws in, snug not hard

Slide both long screws through the whole stack and start them by hand. Tighten them evenly, a little at a time. Then the shorter screw. They go into light metal and plastic, so stop when they are snug.

Filter housing back on over the carb
Housing back on over the carb, long screws going in. Still from the Hipa Store video.
19

Fuel line on

Push the line fully onto the carb stub and slide the clip back over it. Refit the breather hose.

20

Check the trigger

Squeeze the throttle trigger. The lever on the carb should open all the way and snap back to idle by itself.

21

Cover, starter, filter

Engine cover and starter back on with their eight screws. New air filter and the prefilter in, filter cover on with its two screws. Push the boot back onto the spark plug until it clicks.

First start
22

Fuel and leak check

Fill with fresh 50:1 and close the cap. Look at the grommet and both ends of the line for a minute. Any wet spot gets fixed before starting.

23

Start it

Stop switch on, choke on, and pull. A dry line takes several pulls to fill. When it fires, turn the choke off and let it idle.

24

Leave the carb screws alone at first

A new carb comes preset. Run it for a few minutes and try full throttle before touching anything.

25

If it needs tuning

Stihl's standard setting: turn the H and L screws counterclockwise as far as they go. Then turn the idle screw LA clockwise until it idles smoothly. Idle speed is 3,100 rpm.

If it will not behave
What it doesLook at
Fires, then diesThe filter in the tank, a kinked line, or the gasket hole covered
Will not draw fuel at allLine not through the grommet into the fuel, or the stack built with the gaskets swapped
Bogs when you squeeze the triggerThrottle cable not seated in the swivel, or the L screw too lean
Races at idleAn air leak: carb screws loose or a gasket folded
Watch it done
Hipa Store: carb kit install on a BR 420 C (7 min)

The exact blower. Shows what comes off and in what order, the fuel line clip, the throttle cable and the gasket stack. Watch this one first.

Elisha's Repair: BR 420 carburetor replacement (26 min)

Slow and close up on putting the new carb on: gaskets, long screws, throttle cable. At the end it will not stay running until he changes the filter in the tank.

Elisha's Repair: BR 420 Magnum repair, part 1 (22 min)

The same blower with the carb already off. Good look at where everything sits, including the vent stub on the Stihl carb.

The Mower Medic: fuel line, grommet and filter on a BR 380 (10 min)

The sister model, same tank and same single fuel line. The whole fuel line job from start to finish, including pulling the old hose out of the tank and seating the grommet.

Carl's Small Engine Repair: BR 420 with a bad tank vent (1 min)

What a blocked tank vent does: starves for fuel and bogs when you open the throttle.

Parts Store: BR 380 carburetor replacement (9 min)

Sister model again. A second look at the carb swap if the first two leave a question.

Sunshine TV: rebuilding the Walbro carb on a BR 420 (13 min)

Only if you would rather put new diaphragms in the old Stihl carb than fit the new one.

Not confirmed

These steps were put together from Stihl's manual and parts list and from two repair videos, not from this exact blower on a bench. Screw counts and positions can differ by year. Count them as they come out.

Whether this blower has a primer bulb. Stihl's drawings show none.

How the kit's fuel line and grommet fit the hole in this tank. If the grommet is loose in the hole, keep Stihl's shaped hose and elbow and replace only the filter and the short hose to the carb.

The pictures show another BR 420 C, not this one.

Tightening torque for the carb screws. Stihl's owner manual does not give one.

Where this came from

Stihl BR 420 C owner manual: fuel mix, standard carb setting, idle speed.

Stihl BR 420 spare parts list: the screws, gaskets, filter housing, fuel hoses, pickup and grommet.

Hipa Store: carb kit install on a BR 420 C: the order things come off.

Elisha's Repair: BR 420 carburetor replacement: the gasket stack, the throttle cable and the tank filter.