← All guides

Spark plug

Stihl BR 420 C Magnum

Swap the spark plug. Ten minutes, one wrench, nothing else comes off.

Gap 0.020 in (0.5 mm)
Cold engine only. A hot plug strips the threads.
Have on hand

The plug

NGK BPMR7A or Bosch WSR 6 F. Those are the two Stihl lists for this blower.
Skip the L7T plug that comes in the carb kit. Cross-reference charts match it to the NGK BPM7A, the version without a resistor, and Stihl says resistor plugs only on this blower.

Tools

3/4 in (19 mm) spark plug socket, or the combination wrench that came with the blower
Feeler gauge or a plug gap tool
A rag or a small brush
Old plug out
1

Make it safe

Slide the stop switch to 0. Let the engine cool until you can hold a hand on it.

2

Pull the boot

The plug sits at the top of the engine with a rubber boot over it. Grip the boot itself and pull straight off with a twist. Do not pull on the wire.

Stihl BR 420 C from the starter side
A BR 420 C from the starter side. The black cap on top of the red engine cover is the spark plug boot. Still from the Hipa Store video.
Stihl diagram of the cylinder with the spark plug on top
Under the cover: the plug screws into the top of the cylinder. From Stihl's spare parts list.
3

Clean around it

Brush or wipe the dirt away from the base of the plug so none drops into the engine when it comes out.

4

Unscrew it

Fit the socket square on the plug and turn counterclockwise. If it fights you, stop, give it a drop of oil and ten minutes, and try again.

5

Read the old plug

Light brown or gray tip: running right. Black and sooty: too much fuel or a clogged air filter. Wet and oily: flooded, or too much oil in the mix. White and blistered: running lean and hot, look for an air leak at the carb.

New plug in
6

Check the gap

Slide the 0.020 in (0.5 mm) gauge between the two electrodes. It should drag lightly. To close the gap, tap the bent electrode gently on a hard surface. To open it, pry only on the bent one, never on the center.

7

Check the terminal nut

If the new plug has a small screw-on cap at the top, make sure it is on and tight. The boot grips that cap.

8

Start it by hand

Thread the plug in with your fingers for the first few turns. It should spin in easily. If it binds, back it out and start again: it is cross-threaded.

9

Tighten

Run it down until the washer touches, then about half a turn more with the wrench for a new plug. A plug that has been in before only needs about an eighth of a turn.

10

Boot back on

Push the boot down over the plug until you feel it seat. Tug it lightly to check.

11

Start it

Stop switch on, choke on if the engine is cold, and pull.

The numbers
WhatValue
PlugNGK BPMR7A or Bosch WSR 6 F (resistor type)
Stihl part number0000 400 7000 (NGK), 1110 400 7005 (Bosch)
Gap0.020 in (0.5 mm)
ThreadM14 x 1.25, 0.37 in (9.5 mm) long
Wrench3/4 in (19 mm)
Plug boot, if crackedStihl 1106 405 1000
When to change it

Stihl says to fit a new plug after about 100 hours of running, or sooner if the electrodes are badly worn. Check it first whenever the engine is hard to start, loses power or idles badly.

A new plug that fouls black again within a few hours is telling you about the fuel or the air filter, not the plug.

If the engine floods: plug out, dry it off, hold the throttle wide open and pull the rope a few times to clear the cylinder, then refit.

Watch it done

No one has made a video of just the plug change on this model that turned up. It is three steps: boot off, plug out, plug in.

Hipa Store: BR 420 C, the plug boot coming off (starts at 1:40)

The exact blower. Shows where the plug and its boot sit on top of the engine cover.

Turning Wrenches: BR 420 Magnum will not start (starts at 5:20)

The plug is out of this one while he works through a no-start.

The Mower Medic: BR 380 fuel leak (10 min)

Not about the plug, but the clearest tour of this family of blowers if you want to see the whole machine first.

Not confirmed

Stihl's owner manual gives no tightening torque for the plug. The half turn is NGK's general figure for a new plug of this size with a washer.

The manual shows no cover over the plug on this model, only the boot. If yours has a cover in the way, it is the engine cover described in the carb guide.

The photo shows another BR 420 C, not this one.

Where this came from

Stihl BR 420 C owner manual: plug types, gap, thread and the removal steps.

Stihl BR 420 spare parts list: part numbers for the plugs and the boot.